Valentines Wings and Heart Door Hanger

So I needed something cute for my door I thought I would create a  valentines door hanger. Most of the stuff I have I got from the dollar store which isn’t a bad thing its just they tend to fall apart a lot quicker than most decor. Valentines and Easter are the two holidays I have very little decor for. I think my Halloween and Christmas decor have taken over all my tote’s lol.

I have always been in love with the angel wings but never wanted to spend a lot of money for them. I found a way to make them for cheap from this post. I thought it would be easy to make my own door hanger but in my own way. I used a box we had laying around from when we moved into our house. Even if you had a half sheet of cardboard that would work too. It doesn’t take much cardboard for this Valentine’s wing and heart door hanger.

I also want to point out most of my projects are not completed in a day. Yes, you probably could finish it in a day but I have two little boys and a husband that I love to spend time with. This project has taken me two weeks to finish. The first day I did the base of the project and then it sat in my craft room on the table for a week.  Then I did the joint compound and that sat for a few days to completely dry. Then it was off to final touches of spray paint. I am not a perfect project doer but it gets done eventually. Just know you don’t have to finish stuff in a day it can take time.

This post contains affiliate links for your convenience, please see my disclosure for more info about it.

Items you will need for the project

  1. Cardboard
  2. wall joint compound I bought mine at Wal-Mart already premixed it makes it easier for a project like this. Plus a bonus if you have spots in walls that need filling you have the joint compound to fill them in 🙂
  3. A stick to help with the joint compound I used skewers
  4. Exacto knife and scissors to cut out the pieces
  5. A small piece of 220 grit sand paper
  6. White spray paint
  7. gold spray paint or gold paint optional
  8. A heart for the middle. I had a hard time picking one out but I found the wire one I got from Wal-Mart.

So here are the instructions to create your own. Please forgive me if you look at the pictures I had a hard time freehanding wings 🙂

First step

You will need to cut out the wings base from cardboard. I did my wings attached to each other you can do it all sorts of ways too. I was going to make two separate wings and then connect them in the middle and add the heart. I thought this might be a little easier doing it in one full piece. I used an Exacto knife to cut it out. Using the Exacto knife made it a lot easier than trying to use scissors for this part. I found later on that using scissors was easier on the cutting out the little feathers.

 

Second step

You will need to cut out long feathers from cardboard. I made a paper templet then drew a bunch on the cardboard to cut out. I used 12 feathers I would suggest maybe up to 14 to fill it in some more.

Third step

Cut out medium feathers. As with the long feathers, I used a paper templet and drew it on the cardboard and cut it out. I cut out 24 of this size.

Fourth Step

Cut out Small feathers. Using a paper templet to draw and cut out. I cut out  44 of these feathers.

Fifth Step

You will need to hot glue the feathers to the wings this helps so the pieces don’t fall off. I glued the long feathers first stacking a few on top. Then I glued the medium feathers down. Last I glued the small feathers down. Starting with the large feathers makes it easier in the long run because you have to stack the smaller feathers on top to create a fuller more 3-D look.

Tip: I added paper around the edge to give it a little bit more fullness when I filled it in with the joint compound.

Sixth step

You will take wall joint compound and cover the front of the wings with it. Once it is covered you can take a stick or toothpick etc. to move the joint compound out and around each feather. You may want to fill in the sides fo the cardboard as well so you don’t see the corrugated cardboard showing.

Seventh Step

Take a small piece of sand paper and sand it down a little bit just the pointed edges of the Joint compound.

Eighth Step

You will want to spray paint it white or any color you want. Me personally I like white wings. You can choose to leave it with the white (colored) or you can spray paint or paint spots gold or silver for extra pizzazz. You can see I added a little gold on the top of the white.

Ninth Step

I added some cute ribbon on the back of the wings to make it more stable on my door. With opening and closing the door I didn’t want it to fall off the door and break. by adding a string or ribbon it helps keep it on the door then if I were to attach it to the middle of the wings. You may come up with something more creative to hold your wings.

I bought the cute heart at Wal-mart  I love it 🙂 You can put any heart in the middle or leave it just with the wings too! No matter what you do it will look so cute!

 

Finished Project

I am in love with these wings after looking at my door it might be time for a blue door upgrade 🙂 I need a better-looking door this ugly maroon is bugging me so bad. I hope this project isn’t too hard for you. Sometimes the wall joint compound can get messy.  I feel like it takes practice and patience to get to where you feel ok about what you make. I know some of my first projects didn’t turn out the way I wanted them too! I had a lot of thrown away projects lol.

 

Here are some more post you may like that are like this post

Build your own Jack Skellington 

Build your own BB8

 

Please note while I do DIY and tutorials I am by no means a professional please read through each post carefully and consult a professional when needed.  I will not be responsible for injuries or damages while following a tutorial from my site. All tutorials are done at your own risk. Please be safe and smart while doing projects.

Leave a Reply

Your email address will not be published. Required fields are marked *